Atmel ATtiny45-20XU TSSOP(8) Device
Adapters for Automated Programmers
| 6th Gen | 7th Gen | 9th Gen |
| FASMR08TSH | FX4ASMR08TSH, FASMR08TSH, WX4ASMR08TSH (repl.) | WX4ASMR08TSH |
Adapters for Manual Programmers
| 6th Gen | 7th Gen | 9th Gen |
| FSMR08TSH, FASMR08TSH | FX4SMR08TSH, FSMR08TSH, FX4ASMR08TSH, FASMR08TSH, WX4ASMR08TSH (repl.) | WX4ASMR08TSH |
Adapters for Engineering Programmers
| 6th Gen | 7th Gen |
| FSMR08TSH, FASMR08TSH | FX4SMR08TSH, FSMR08TSH, FX4ASMR08TSH, FASMR08TSH, WX4ASMR08TSH (repl.) |
Last Updated: 05/18/2023
If the device is not yet supported by your BPM programmer (Generation), request Device Support
Note
IMPORTANT:
| Device Type: | Microcontroller |
| Device Size: | 4 Kbyte |
| Algorithm Programming Method: | High-voltage Serial Programming |
Memory Organization:
| Memory Type |
Attributes(*)
|
Included in default Range (Y/N) | DUT Physical Byte Address(hex)(if this area is selected/Activated) | BPWin Buffer Byte Address(hex) |
| Program Memory | [R/W/E] | [Yes] | [0000-0FFF] | [0000-0FFF] |
| [EEPROM Data Memory] | [R/W/E] | [Yes] | [ 1000-10FF] | [ 1000-10FF] |
| Default Algorithm Range | — | — | [0000-10FF] | [0000-10FF] |
* R:Read only W: One time programmable (OTP) R/W: readable and one time programmable (OTP) R/W/E: readable and rewritable if not locked. Any configurations listed under Device-Specific’ in the menu item Device-> Settings will be written to the DUT during ‘Program’ operation regardless of memory range selection. Special Device Considerations:
| Option | Description | Default | Supported (Y/N)? |
| [Fuse Low Byte] | [Please see device specification for the setting] | [62] | [Yes] |
| [Fuse High Byte ] | [Please see device specification for the setting] | [DF] | [Yes] |
| [Fuse Extended Byte] | [Reserved bits should be set to 1] | [FF] | [Yes] |
| 1. | Serialization Supported: | Yes | ||||||||||||
| 2. | [Secure/Lock Erasable]: | Yes | ||||||||||||
| 3. | [Special file format required]: | No | ||||||||||||
| 4. | Erase will erase both Flash and EEPROM.In the Device Configureif CALIBRATION is set to ENABLE the Calibration byte can be programmed into | |||||||||||||
| any address [0-10FF] in the Flash memory or EEPROM.The address is set in CALIBRATION ADDRESS option. | ||||||||||||||
CAL BYTE ADDRESS option is to set address 0h in the signature row high byte for 8.0MHz internal RC Oscillator Calibration.
|
| New devices may automatically calibrate the RC Oscillator.
|
| Please set the CALIBRATION option to DISABLE(default) to use automatic calibration.
| 5. |
COMPARE operation will only verify data read from the device against data in the buffer.
|
| The Calibration byte will be ignored during compare regardless of the Calibration settings in Device Configure. |
| ||||||
‘
BPM does not sell programmable devices, nor do we program devices directly. BPM makes programmers and accessories to make programming in-house fast, easy, and profitable.
Additional information
| Manufacturer | Atmel |
|---|---|
| Packages | TSSOP(8) |
| Part Number | ATtiny45-20XU |
| Vcc(program) | 5 |
| 8-bit Bytes | |
| Package |