Atmel AT89C51CC03U-S3SIM PLCC(52) Device
Adapters for Automated Programmers
| 6th Gen | 7th Gen |
| FASM52PC, FASM52P, FASM52PI, FASM52PD | FASM52PC, FASM52P, FASM52PI, FASM52PD |
Adapters for Manual Programmers
| 6th Gen | 7th Gen |
| FSM52PC, FSM52PCA, FSM52P, FSM52PA, FSM52PH, FSM52PMBW, FSM52PI, FSM52PD, FSM84UP, FASM52PC, FASM52P, FASM52PI, FASM52PD, FSM84AH (obs.), FSM84UPB (obs.), FSM84AHA (obs.) | FSM52PC, FSM52PCA, FSM52P, FSM52PA, FSM52PH, FSM52PMBW, FSM52PI, FSM52PD, FSM84UP, FASM52PC, FASM52P, FASM52PI, FASM52PD, FSM84AH (obs.), FSM84UPB (obs.), FSM84AHA (obs.) |
Adapters for Engineering Programmers
| 6th Gen | 7th Gen |
| FSM52PC, FSM52PCA, FSM52P, FSM52PA, FSM52PH, FSM52PMBW, FSM52PI, FSM52PD, FSM84UP, FASM52PC, FASM52P, FASM52PI, FASM52PD, FSM84AH (obs.), FSM84UPB (obs.), FSM84AHA (obs.) | FSM52PC, FSM52PCA, FSM52P, FSM52PA, FSM52PH, FSM52PMBW, FSM52PI, FSM52PD, FSM84UP, FASM52PC, FASM52P, FASM52PI, FASM52PD, FSM84AH (obs.), FSM84UPB (obs.), FSM84AHA (obs.) |
Last Updated: 05/18/2023
If the device is not yet supported by your BPM programmer (Generation), request Device Support
Note
IMPORTANT: Code Revision 1.1 updated PLCC52 pin out to match Rev C programming specification from Atmel.Microcontroller with Flash.In the Buffer 64KB User Memory is mapped into 0000h-FFFFh2KB Data Memory (EEPROM) is mapped into 10000h-107FFh and2KB Boot Memory is mapped into 10800h-10FFFh.The Data Memory and Boot Memory are treated as a single block.Each block can be ERASED/PROGRAMMED separately by setting Ranges under Device Options.The following range setting corresponds to each block: 00000h-0FFFFh (Flash Memory)10000h-10FFFh (Data Memory and Boot Memory)Part can be secured by programming Lock bits 0 through 2 of HSB using Secure command.Bit 0 (LB0): Parallel programming is disabled.Bit 1 (LB1): Parallel program/verify are disabled.Bit 2 (LB2): Parallel program/verify/external execution are disabled.Bits 3 4 5 of HSB are reserved bits. Bits 6 7 of HSB are set under Device Configure (X2 & BLJ).Device Configure has the XAF parameters necessary when programming a CAN bootloader into Boot memory area.Check electronic identifiers (ID)’ must be ENABLED under Device/Options.Certain combinations of Configure options and Boot memory may not allow the device to runcorrectly for a stand alone verify. ‘
BPM does not sell programmable devices, nor do we program devices directly. BPM makes programmers and accessories to make programming in-house fast, easy, and profitable.
Additional information
| Manufacturer | Atmel |
|---|---|
| Vcc(program) | 5 |
| Packages | PLCC(52) |
| Part Number | AT89C51CC03U-S3SIM |
| Package | |
| 8-bit Bytes | |
| ByteWidth | AT89C51CC03U-S3SIM (ID=FFFEh) |
| VppProgram | 69632 |
| ElectricalErase | 5 |