Atmel ATtiny26-16MC LAP(32) Device
Adapters for Automated Programmers
| 6th Gen | 7th Gen |
| FASMR32MLFKE, FASM32MLFA, FASMR32MLFA, FASMR32MLFR | FASMR32MLFKE, FASM32MLFA, FASMR32MLFA, FASMR32MLFR |
Adapters for Manual Programmers
| 6th Gen | 7th Gen | 9th Gen |
| FSMR32MLFKE, FSM32MLF, FASMR32MLFKE, FASM32MLFA, FSMR32MLFA, FSMR32MLFR, FASMR32MLFA, FASMR32MLFR, LX4ASMR32MLFR (repl.), LASMR32MLFKE (repl.), WASMR32MLFA (repl.) | FSMR32MLFKE, FSM32MLF, FASMR32MLFKE, FASM32MLFA, FSMR32MLFA, FSMR32MLFR, FASMR32MLFA, FASMR32MLFR, LX4ASMR32MLFR (repl.), LASMR32MLFKE (repl.), WASMR32MLFA (repl.) | LX4ASMR32MLFR, LASMR32MLFKE, WASMR32MLFA |
Adapters for Engineering Programmers
| 6th Gen | 7th Gen |
| FSMR32MLFKE, FSM32MLF, FASMR32MLFKE, FASM32MLFA, FSMR32MLFA, FSMR32MLFR, FASMR32MLFA, FASMR32MLFR, LX4ASMR32MLFR (repl.), LASMR32MLFKE (repl.), WASMR32MLFA (repl.) | FSMR32MLFKE, FSM32MLF, FASMR32MLFKE, FASM32MLFA, FSMR32MLFA, FSMR32MLFR, FASMR32MLFA, FASMR32MLFR, LX4ASMR32MLFR (repl.), LASMR32MLFKE (repl.), WASMR32MLFA (repl.) |
Last Updated: 05/18/2023
If the device is not yet supported by your BPM programmer (Generation), request Device Support
Note
IMPORTANT: This algorithm uses Serial Mode for Read/Compare/Verify programming either SPIEN bit to 1 orRSTDISBL bit to 0 will disable the Serial Mode. Therefore the Read/Compare/Verify command (includingID check) will fail if the Serial Mode is disabled.Buffer address range 0000h-7FFh is FLASH Program Memory and 800h-87Fh is EEPROM Data Memory.There are four Calibration Bytes residing in the signature row high byte ofaddresses 0000h 0001h 0002h and 0003h. They are for 1 2 4 and 8 MHz internal RC Oscillator calibrationrespectively. To program one of these four calibration bytes under Device Configure menu1)Set CALIBRATION to ENABLE2)Set CAL BYTE ADDRESS to one of the four Calibration Byte addresses (00h-03h).3)Set CALIBRATION ADDRESS to the memory address you want to program the Calibration Byte (from 0000h to 87Fh).New devices may automatically calibrate the RC Oscillator.Please set the CALIBRATION option to DISABLE(default) to use automatic calibration.**** To program the Fuse Low Byte Fuse High Byte and Lock Bit Byte under Device Configuremenu Secure must be enabled. ****
BPM does not sell programmable devices, nor do we program devices directly. BPM makes programmers and accessories to make programming in-house fast, easy, and profitable.
Additional information
| Manufacturer | Atmel |
|---|---|
| Packages | LAP(32) |
| Part Number | ATtiny26-16MC |
| Set programming | Yes |
| Vcc(program) | 5 |
| 8-bit Bytes | |
| Package |