Freescale Semiconductor MC9S12XA512CFU QFP(80) Device

Adapters for Automated Programmers

Adapters for Manual Programmers

Adapters for Engineering Programmers

Last Updated: 05/18/2023

IMPORTANT: The following describes the Buffer setup: Addresses [$000C00 – $000FFF]are EEPROM fixed page $FF. Addresses [$00C000 – $00FFFF]are Fixed flash page $FF. Addresses [$E08000 – $E0BFFF]are FLASH PAGE $E0. Addresses [$E18000 – $E1BFFF]are FLASH PAGE $E1. Addresses [$E28000 – $E2BFFF]are FLASH PAGE $E2. Addresses [$E38000 – $E3BFFF]are FLASH PAGE $E3. Addresses [$E48000 – $E4BFFF]are FLASH PAGE $E4. Addresses [$E58000 – $E5BFFF]are FLASH PAGE $E5. Addresses [$E68000 – $E6BFFF]are FLASH PAGE $E6. Addresses [$E78000 – $E7BFFF]are FLASH PAGE $E7. Addresses [$E88000 – $E8BFFF]are FLASH PAGE $E8. Addresses [$E98000 – $E9BFFF]are FLASH PAGE $E9. Addresses [$EA8000 – $EABFFF]are FLASH PAGE $EA. Addresses [$EB8000 – $EBBFFF]are FLASH PAGE $EB. Addresses [$EC8000 – $ECBFFF]are FLASH PAGE $EC. Addresses [$ED8000 – $EDBFFF]are FLASH PAGE $ED. Addresses [$EF8000 – $EFBFFF]are FLASH PAGE $EF. Addresses [$F08000 – $F0BFFF]are FLASH PAGE $F0. Addresses [$F18000 – $F1BFFF]are FLASH PAGE $F1. Addresses [$F28000 – $F2BFFF]are FLASH PAGE $F2. Addresses [$F38000 – $F3BFFF]are FLASH PAGE $F3. Addresses [$F48000 – $F4BFFF]are FLASH PAGE $F4. Addresses [$F58000 – $F5BFFF]are FLASH PAGE $F5. Addresses [$F68000 – $F6BFFF]are FLASH PAGE $F6. Addresses [$F78000 – $F7BFFF]are FLASH PAGE $F7. Addresses [$F88000 – $F8BFFF]are FLASH PAGE $F8. Addresses [$F98000 – $F9BFFF]are FLASH PAGE $F9. Addresses [$FA8000 – $FABFFF]are FLASH PAGE $FA. Addresses [$FB8000 – $FBBFFF]are FLASH PAGE $FB. Addresses [$FC0800 – $FC0BFF]are EEPROM Page $FC. Addresses [$FC8000 – $FCBFFF]are FLASH PAGE $FC. Addresses [$FD0800 – $FD0BFF]are EEPROM Page $FD. Addresses [$FE0800 – $FE0BFF]are EEPROM Page $FE. Addresses [$FE8000 – $FEBFFF]are FLASH PAGE $FE. FLASH PAGE $FD can be set under Device configure. Flash Nonvolatile byte is mapped to Buffer address $FF0E and Flash Security byte is mapped to Buffer address $FF0F. These two can also be set using Device Configure. The two bytes are ignored during Program and Verify. To Program these two bytes the Device Configure options must be set and the Secure command must be Enabled. Once the Device has been secured the programmer can no longer access it. Please set Device->Byte order to: ‘Big Endian’. ‘