Philips Semiconductors P89LPC908 (SOIC8) SOIC(8) Device
Adapters for Automated Programmers
| 6th Gen | 7th Gen |
| FASM08SN, FASM08SR, FASM16SAT, FASM16SA, FASM14SA, FASM08SA (obs.) | FASM08SN, FASM08SR, FASM16SAT, FASM16SA, FASM14SA, FASM08SA (obs.) |
Adapters for Manual Programmers
| 6th Gen | 7th Gen | 9th Gen |
| FSM08SN, FSM08SR, FSM08S, FSM16SAT, FSM16SA, FSM14SA, FSM16S, FASM08SN, FASM08SR, FASM16SAT, FASM16SA, FASM14SA, FSM08SA (obs.), FASM08SA (obs.), WX4ASM08SN (repl.) | FSM08SN, FSM08SR, FSM08S, FSM16SAT, FSM16SA, FSM14SA, FSM16S, FASM08SN, FASM08SR, FASM16SAT, FASM16SA, FASM14SA, FSM08SA (obs.), FASM08SA (obs.), WX4ASM08SN (repl.) | WX4ASM08SN |
Adapters for Engineering Programmers
| 6th Gen | 7th Gen |
| FSM08SN, FSM08SR, FSM08S, FSM16SAT, FSM16SA, FSM14SA, FSM16S, FASM08SN, FASM08SR, FASM16SAT, FASM16SA, FASM14SA, FSM08SA (obs.), FASM08SA (obs.), WX4ASM08SN (repl.) | FSM08SN, FSM08SR, FSM08S, FSM16SAT, FSM16SA, FSM14SA, FSM16S, FASM08SN, FASM08SR, FASM16SAT, FASM16SA, FASM14SA, FSM08SA (obs.), FASM08SA (obs.), WX4ASM08SN (repl.) |
Last Updated: 05/18/2023
If the device is not yet supported by your BPM programmer (Generation), request Device Support
Note
IMPORTANT: Microcontroller with 1Kb Flash.Please set the default buffer value to 0h.The Device is verified using the Sum capability of the device.The expected checksum is calculated and compared to the checksum read from the device.When the Boot Status Bit is set the contents of the Boot Vector is used as the high byteof the execution address and the low byte is set to 00H.***** To program the options in Device Config menu you must select the appropriate optionsin that menu AND you must ENABLE secure. Otherwise none of the options will be programmed. *****The device has three security bits for a sector. If only security bit 0 is programmed then the devicecannot be verified. Bit 0 can be erased using sector erase. If security bit 2 is programmedthen the bit and the corresponding sector can only be erased by erasing the entire device.The configuration options are mapped to the following buffer locations: UCFG1-FF00h Bootvector-FF02hBoot Status Bit-FF03h Sec 0-FF04h Sec 1-FF05h Sec 2-FF06h Sec 3-FF07h. Please load the defaultvalues for these options in the buffer if these options are not required to be programmed. Please referto the Philips data sheet for further information.
BPM does not sell programmable devices, nor do we program devices directly. BPM makes programmers and accessories to make programming in-house fast, easy, and profitable.
Additional information
| 8-bit Bytes | 1024 |
|---|---|
| Manufacturer | Philips Semiconductors |
| Packages | SOIC(8) |
| Part Number | P89LPC908 |
| Set programming | Yes |
| Vcc(program) | 3.3 |
| Package |